Sergio´s LAZZOR

Post your build logs here

Sergio´s LAZZOR

Postby soehler » Tue Aug 23, 2011 3:47 am

Oficial.jpg
Official Photo

The adventure has begun !
soehler
 
Posts: 69
Joined: Mon Apr 11, 2011 1:23 am

Taping Night

Postby soehler » Tue Aug 23, 2011 3:53 am

Tapping.jpg

Today I started the build.

Reading instructions and, 40 minutes taping the Misumi extrusions for the LAZZOR feet.
soehler
 
Posts: 69
Joined: Mon Apr 11, 2011 1:23 am

Building the main frame

Postby soehler » Sun Aug 28, 2011 8:59 pm

Built almost the entire main frame today stoped at the last two extrusions because I went out of 10mm M5 screws :-)
I wull buy some more tomorrow.
By the way, I am replacing all steel screws by stainless steel ones, it will avoid rusting, due to high humidity here.

So far so good, enjoying the build

!
MainFrame.jpg
soehler
 
Posts: 69
Joined: Mon Apr 11, 2011 1:23 am

Re: Sergio´s LAZZOR

Postby soehler » Tue Aug 30, 2011 2:29 am

FrameComplete.jpg

Got the M5 screws today, main frame complete !
soehler
 
Posts: 69
Joined: Mon Apr 11, 2011 1:23 am

Re: Sergio´s LAZZOR

Postby soehler » Mon Sep 26, 2011 1:43 am

Rio de Janeiro-20110903-00571.jpg


VRails glued and looking good
soehler
 
Posts: 69
Joined: Mon Apr 11, 2011 1:23 am

Re: Sergio´s LAZZOR

Postby soehler » Mon Sep 26, 2011 1:45 am

Rio de Janeiro-20110904-00572.jpg

Bearings pressed into hdpe parts
Original rods replaced by stainless steel ones.
Last edited by soehler on Mon Sep 26, 2011 1:48 am, edited 1 time in total.
soehler
 
Posts: 69
Joined: Mon Apr 11, 2011 1:23 am

Re: Sergio´s LAZZOR

Postby soehler » Mon Sep 26, 2011 1:47 am

Rio de Janeiro-20110904-00574.jpg

Z-Rods being prepared
soehler
 
Posts: 69
Joined: Mon Apr 11, 2011 1:23 am

Re: Sergio´s LAZZOR

Postby soehler » Mon Sep 26, 2011 1:51 am

Rio de Janeiro-20110904-00580.jpg

Z-table lifts in place
soehler
 
Posts: 69
Joined: Mon Apr 11, 2011 1:23 am

Re: Sergio´s LAZZOR

Postby soehler » Mon Sep 26, 2011 2:11 am

Honeycomb as it arrives, compressed (pre cut to 2 cm height)
Rio de Janeiro-20110907-00586.jpg


Expanding honeycomb, attached first combs to plywood with T-pins and started to expand it with my hands(bare ! do not do this.), do it nice and slow, it is hard to make the combs perfect.
CAUTION: USE GLOVES TO PROTECT YOUR HANDS, IT CUTS BADLY AND CAN SERIOUSLY INJURY YOUR HANDS
Rio de Janeiro-20110907-00588.jpg


Place table on top of expanded honeycomb and cut it slightly bigger than the inner dimension of the table
Rio de Janeiro-20110907-00590.jpg


I used aluminum corners (5) attached to the bottom of the table to support honeycomb
Rio de Janeiro-20110910-00592.jpg

Rio de Janeiro-20110910-00593.jpg


Table ready
Rio de Janeiro-20110910-00595.jpg


Table installed (bottom view)
IMG-20110920-00629.jpg
soehler
 
Posts: 69
Joined: Mon Apr 11, 2011 1:23 am

Re: Sergio´s LAZZOR

Postby soehler » Mon Sep 26, 2011 2:17 am

Building the gantry
Rio de Janeiro-20110910-00597.jpg

Rio de Janeiro-20110910-00596.jpg
soehler
 
Posts: 69
Joined: Mon Apr 11, 2011 1:23 am

Next

Return to Build Logs

Who is online

Users browsing this forum: No registered users and 3 guests