Configuration.h for Hadron with SeemeCNC EZstruder

Topics Related to the ORD Bot Printer

Configuration.h for Hadron with SeemeCNC EZstruder

Postby fsamir » Wed Dec 25, 2013 3:45 am

Hi all,

can someone please send me a Configuration.h for a Hadron with SeemeCNC ezstruder?

I got a second hand hadron and it didn't come with the firmware.

Thanks
Franklin Dattein
fsamir
 
Posts: 9
Joined: Sat Dec 21, 2013 8:19 am

Re: Configuration.h for Hadron with SeemeCNC EZstruder

Postby flickerfly » Tue Feb 04, 2014 2:56 pm

That's a pretty general question and really depends more on your electronics than the SeeMeCNC extruder. Do you have an Azteeg X1, X3, RAMPS, etc. Also, which firmware are you wanting to use Repetrier Firmware, Marlin, etc. Also, what endstops and where are they located, this matters in how your configuration.h is setup.

That's the tip of the iceberg.
flickerfly
 
Posts: 247
Joined: Sat Apr 27, 2013 10:04 pm
Location: Allentown, PA

Re: Configuration.h for Hadron with SeemeCNC EZstruder

Postby fsamir » Wed Feb 05, 2014 3:30 am

RAMPS 1.4, Marlin FW (but any FW would be fine), magnetic endstops (but I am not interested in this bit of the config).

I should have mentioned that I am particularly interested in solving a problem with filament slip. I have already tweaked a Marlin config, but filament keeps slipping and I wanted to have a base for comparison. Makes sense?
Franklin Dattein
fsamir
 
Posts: 9
Joined: Sat Dec 21, 2013 8:19 am

Re: Configuration.h for Hadron with SeemeCNC EZstruder

Postby flickerfly » Wed Feb 05, 2014 1:45 pm

You may want to look at topic 2050 for details on configuring the SeeMeCNC EZstruder. The calculations that Bart Dring did for it have worked well for me. The rest of the stuff should be irrelevant as it regards filament slipping. The hotend may be involved. When you say slipping, what do you mean? Do you have any images?

viewtopic.php?f=27&t=2050
flickerfly
 
Posts: 247
Joined: Sat Apr 27, 2013 10:04 pm
Location: Allentown, PA

Re: Configuration.h for Hadron with SeemeCNC EZstruder

Postby fsamir » Thu Feb 06, 2014 1:05 am

Thanks, I will have a at the topic.

By slipping I mean that I can hear it slipping and see the motor going backwards a couple of mm every time it happens.
Franklin Dattein
fsamir
 
Posts: 9
Joined: Sat Dec 21, 2013 8:19 am

Re: Configuration.h for Hadron with SeemeCNC EZstruder

Postby fsamir » Thu Feb 06, 2014 4:00 am

I've checked the topic and that is the one I'd used to setup my printer. Yet, the filament slips :S
Franklin Dattein
fsamir
 
Posts: 9
Joined: Sat Dec 21, 2013 8:19 am

Re: Configuration.h for Hadron with SeemeCNC EZstruder

Postby flickerfly » Thu Feb 06, 2014 2:03 pm

Are you describing skipping steps? Have you adjusted the pots on the motor driver?
flickerfly
 
Posts: 247
Joined: Sat Apr 27, 2013 10:04 pm
Location: Allentown, PA

Re: Configuration.h for Hadron with SeemeCNC EZstruder

Postby fma » Thu Feb 06, 2014 2:12 pm

Yes, I think this is fsamir's problem, as he said:

[...]and see the motor going backwards a couple of mm every time it happens


What config are your using? Bowden-ed, or normal extruder? I recently switched to Bowden, and my motor is not powerfull enough to drive the filament at my previous printing speed (100mm/s)... I plan to order a bigger motor:

http://www.ebay.fr/itm/Nema17-92Onz-in- ... 2587af708f
Frédéric
fma
 
Posts: 213
Joined: Mon Aug 20, 2012 7:53 am

Re: Configuration.h for Hadron with SeemeCNC EZstruder

Postby fsamir » Thu Feb 06, 2014 9:15 pm

Direct drive extruder.

Pior to the Ezstruder I was using a Makergear extruder, which has got a gear box and is much more forgiving and allowed for higher speeds.
Franklin Dattein
fsamir
 
Posts: 9
Joined: Sat Dec 21, 2013 8:19 am

Re: Configuration.h for Hadron with SeemeCNC EZstruder

Postby flickerfly » Thu Feb 06, 2014 9:50 pm

Yeah, that's a good point.
flickerfly
 
Posts: 247
Joined: Sat Apr 27, 2013 10:04 pm
Location: Allentown, PA

Next

Return to ORD Bot

Who is online

Users browsing this forum: No registered users and 3 guests