ORD Bot 3D Printer

Post your build logs here

Re: ORD Bot 3D Printer

Postby technowizard12 » Sun Feb 12, 2012 3:46 am

Are you using RAMPS for the control? Do you use the RepRap standard control interface?

My apologies if you answered this already.
technowizard12
 
Posts: 7
Joined: Sat Feb 11, 2012 1:47 am

Re: ORD Bot 3D Printer

Postby bdring » Sun Feb 12, 2012 4:25 am

I am using the RAMPS shield. I am using Sprinter software. I am pretty new to this so I took a low risk well proven easy to use stack

Sprinter
Printrun (pronterface)
Slic3r

You can see the electronics here.

viewtopic.php?f=16&t=1035&start=30#p8344
Bart
"If you didn't build it, you will never own it."
bdring
Site Admin
 
Posts: 2966
Joined: Sun Nov 22, 2009 7:33 pm
Location: Chicago, IL, USA

Re: ORD Bot 3D Printer

Postby JeremyBP » Sun Feb 12, 2012 3:19 pm

The E driver and motor are not even warm.


In that case, try turning the current up a bit.
Compulsive Fabricator
http://tinyworkshop.org
JeremyBP
 
Posts: 208
Joined: Fri Feb 10, 2012 3:37 am
Location: Oak Park, IL

Re: ORD Bot 3D Printer

Postby Gijs » Sun Feb 12, 2012 3:38 pm

Hi Barton,

First of all, I'm impressed by the simplicity, but also the beauty of the design. While I was browsing your shop, I found you don't ship overseas. I am based in the Netherlands. Is there still a way to get access to the kits once it is ready?

Thanks,
Gijs
Gijs
 
Posts: 52
Joined: Sun Feb 12, 2012 3:24 pm

BOM

Postby bdring » Sun Feb 12, 2012 5:45 pm

Here is a first cut at the BOM.

http://www.buildlog.net/cnc_laser/erp/i ... tNo=D30050

There are probably a lot of little errors in it that I will sort out soon. I put very rough assembly drawings in, but need to clean them up a lot. PDFs and DXFs of the piece parts will come within the next few days.

International shipping. I think there are flat rate options that will put shipping in the $45 - $65.
Bart
"If you didn't build it, you will never own it."
bdring
Site Admin
 
Posts: 2966
Joined: Sun Nov 22, 2009 7:33 pm
Location: Chicago, IL, USA

Re: ORD Bot 3D Printer

Postby Guldberg » Sun Feb 12, 2012 8:46 pm

Perfect!

Love the shopping list. A lot of the stuff (makerslide, wheels, spacers etc.) where in the kickstarter set as far as I can tell, so building one of these should be a breeze:-)
Guldberg
 
Posts: 14
Joined: Sun Mar 06, 2011 8:40 pm

Help...Name For Next Size?

Postby bdring » Sun Feb 12, 2012 9:55 pm

I am working on the documentation and prototype for the larger size. I like the name 'Quantum" for the little guy. What should I name the next size?

This uses the standard 210 square MK1/MK2 heated platforms used on a lot of Mendels. I need a good size term like Quantum, but larger. There may be larger size yet, so I need room to grow in the name so I don't want a name that implies "biggest" ORD Bot.

Midi?
Midway (get it?)
Grand?
Grande?
Mega?
Jumbo?
Bubba?
Bart
"If you didn't build it, you will never own it."
bdring
Site Admin
 
Posts: 2966
Joined: Sun Nov 22, 2009 7:33 pm
Location: Chicago, IL, USA

Re: ORD Bot 3D Printer

Postby soehler » Sun Feb 12, 2012 10:05 pm

Bart

What about leap

Quantum Leap

Sergio
soehler
 
Posts: 69
Joined: Mon Apr 11, 2011 1:23 am

Re: ORD Bot 3D Printer

Postby mxk » Sun Feb 12, 2012 10:06 pm

Planck? Stretching a bad pun further, the biggest one could be Max...
mxk
 
Posts: 123
Joined: Wed Jun 08, 2011 11:02 pm

Re: ORD Bot 3D Printer

Postby bdring » Sun Feb 12, 2012 10:19 pm

gORDo?
Bart
"If you didn't build it, you will never own it."
bdring
Site Admin
 
Posts: 2966
Joined: Sun Nov 22, 2009 7:33 pm
Location: Chicago, IL, USA

PreviousNext

Return to Build Logs

Who is online

Users browsing this forum: No registered users and 4 guests