Hadron Build (ATI kit) quick heads up

Topics Related to the ORD Bot Printer

Re: Hadron Build (ATI kit) quick heads up

Postby geoffs » Thu Oct 04, 2012 5:00 am

Got my kit (or part of it) from ATI today. Shipped September 26 so pretty happy with that. (I'm in Australia)
It did include a numbered parts list will corresponded with the numbered baggies.
Nothing seems to be missing but one of the 320mm Makeslides is only 310mm.

The second part of the kit will have the electronics, extruders and heat bed - or so I hope :D
geoffs
 
Posts: 78
Joined: Fri May 06, 2011 12:01 am
Location: Tasmania, Australia

Re: Hadron Build (ATI kit) quick heads up

Postby automationtech » Thu Oct 04, 2012 5:23 pm

geoffs wrote:Got my kit (or part of it) from ATI today. Shipped September 26 so pretty happy with that. (I'm in Australia)
It did include a numbered parts list will corresponded with the numbered baggies.
Nothing seems to be missing but one of the 320mm Makeslides is only 310mm.

The second part of the kit will have the electronics, extruders and heat bed - or so I hope :D


It is on the way to you, you can use the 310 mm in the Z axis. if you have any concern, We will take care

http://www.automationtechnologiesinc.co ... controller
automationtech
 
Posts: 46
Joined: Wed Jul 18, 2012 10:20 pm

Re: Hadron Build (ATI kit) quick heads up

Postby automationtech » Thu Oct 04, 2012 5:26 pm

Nyx_ wrote:Congratulation!

Thanks a lot for the picture and video. Its Amazing it was put together some quickly!!!
Do you think it is possible to improve the quality/resolution of the printed object?
I saw what I think it is a effect of wobbling on the cube edges. Is there any way to reduce that effect?
What was the parameters (speed/layer height, etc) used on the printing video?


I think it takes time to learn how to tune the system.
Last edited by automationtech on Thu Oct 04, 2012 5:28 pm, edited 1 time in total.
automationtech
 
Posts: 46
Joined: Wed Jul 18, 2012 10:20 pm

Re: Hadron Build (ATI kit) quick heads up

Postby automationtech » Thu Oct 04, 2012 5:27 pm

blah_59 wrote:I couldn't tell for sure from the video but are you running the extruder without the heat sink and fan?


see attached picture
Attachments
IMG_0580.JPG
automationtech
 
Posts: 46
Joined: Wed Jul 18, 2012 10:20 pm

Re: Hadron Build (ATI kit) quick heads up

Postby blah_59 » Thu Oct 04, 2012 9:48 pm

Thanks for a pic with a good view angle of the extruder. Do you have room in that setup to take the 2 screws out of the extruder to take the cold end apart if needed without un-mounting it?
blah_59
 
Posts: 158
Joined: Wed Aug 29, 2012 10:08 am

Re: Hadron Build (ATI kit) quick heads up

Postby AVRC » Thu Oct 04, 2012 9:49 pm

It's hard to be sure from the video, but it looks like the layer height is bigger than the extruded filament diameter.
AVRC
 
Posts: 20
Joined: Fri Mar 02, 2012 3:34 pm

Re: Hadron Build (ATI kit) quick heads up

Postby automationtech » Fri Oct 05, 2012 12:34 am

We only have Limited ORD Bot Hadron 3D printer mechanical platform Kit left now

check here for stock

http://www.automationtechnologiesinc.co ... controller
automationtech
 
Posts: 46
Joined: Wed Jul 18, 2012 10:20 pm

Re: Hadron Build (ATI kit) quick heads up

Postby cozmicray » Fri Oct 05, 2012 1:13 am

ATI
I am having trouble getting my ATI Ordbot Hadron running.
I have a RAMPS1.4 shield on a ATMEGA 2560
RAMPS from GADGETS 3D.

I have run RAMPS test code and leds blink and heaters heat
Temperature pins respond to pot across them.
NO motor movement.
I have tried Marlin -- no motor movement.

The stepper motors have Blue, Red, Green, Black leads.
The RAMPS motor connections 2B, 2A, 1A, 1B.
Please tell me how you have them connected?

Tnx
Ray
cozmicray
 
Posts: 168
Joined: Thu Sep 20, 2012 4:32 pm
Location: Blue Bell, PA

Re: Hadron Build (ATI kit) quick heads up

Postby cozmicray » Sun Oct 07, 2012 3:03 am

I solved my problem.
I don't have motor drivers installed.

The Pictures of the RAMPS boards don't have motor driver boards installed.

So as soon as I get 4 motor driver boards plugged in I try again!

Tnx
cozmicray
 
Posts: 168
Joined: Thu Sep 20, 2012 4:32 pm
Location: Blue Bell, PA

Re: Hadron Build (ATI kit) quick heads up

Postby geoffs » Tue Oct 09, 2012 9:48 am

I managed to get my Hadron built in only a couple of hours over two nights.
I printed out several views of the assemblies and this was enough to get the job done.

The only disassembly I had to do was to insert slot nuts for the X axis for things like the feet and to join the Y axis to the main extrusion.
The only complaint I have is that the eccentric nuts seem not to be metric (about 9.5mm) and the allen keys on the Z axis shaft couplers were in between any metric allen keys I had.

The previously mentioned short Makerslide doesn't seem to be an issue in it's current position (X axis) but as suggested, I'll move it to one f the Z axis rails if it becomes so.
Still waiting for the second (electronics) package. I've got the USPS tracking numbder but it shows it's not in the country yet. Soon, soon ...

Regards
Geoff
geoffs
 
Posts: 78
Joined: Fri May 06, 2011 12:01 am
Location: Tasmania, Australia

PreviousNext

Return to ORD Bot

Who is online

Users browsing this forum: No registered users and 38 guests

cron