Anyone still building?

Questions, Suggestions, Tips, Etc

Anyone still building?

Postby ag3c » Fri Apr 18, 2014 9:23 pm

Anyone out there still in the process of the initial 2.x laser build?

I am -- nearing the end, about to install tube and optics.
Posts: 16
Joined: Thu Sep 09, 2010 11:51 pm

Re: Anyone still building?

Postby pourcirm » Fri Apr 18, 2014 10:43 pm

I'm working on a build too. I've increased the footprint a bit and I'm finishing up my frame/skins. I have everything ready to go aside from control and laser tube. Still debating what controller to use. My skins are slowing me down currently because I am marking, cutting, and drilling them by hand.
Posts: 25
Joined: Fri Jun 07, 2013 5:03 pm

Re: Anyone still building?

Postby Chankster » Sat Apr 19, 2014 1:36 am

Working on expanding mine to use a 80w tube.
"This is not my sig", it said. - I looked at it suspiciously; Who's sig was it, then?
Posts: 99
Joined: Tue Mar 08, 2011 5:43 pm
Location: St. Louis, MO

Re: Anyone still building?

Postby leros » Thu Apr 24, 2014 4:39 am

I'm still building as well. I'm going with the stock 2.X design, although I kinda wish I had enlarged it a bit. Oh well.

I've got the frame and gantry completely built. I've gathered all the parts except for a few random odds and ends.

On my TODO list:
- Connect the belts and test the mechanics with the controller
- Mirror mounts from LightObject don't fit the parts in the kit I bought. Gotta figure that out.
- The cable carrier I bought doesn't move freely enough. Need to buy a nicer one.
- Test the laser and the rest of the electronics.
- Wire up the electronics.
- Figure out how to mount all the electronics in the frame.
- Build/find a bench to put this on in my garage
Posts: 35
Joined: Thu Dec 02, 2010 9:06 am

Re: Anyone still building?

Postby jonquinn » Sun Jun 22, 2014 4:03 pm

I am accumulating parts. Some are a little difficult to acquire at this point. The one that will be most difficult at this point is the sheeting. I might be able to pick up a 4x8 sheet from the original source, but will have to get it cut up myself.
Posts: 11
Joined: Sun Jan 05, 2014 4:47 am

Re: Anyone still building?

Postby greenvandan » Sun Jun 22, 2014 10:53 pm

I cut my own panels with a circular saw mostly, used a router/jig to cut vent slots. A decent sign supply shop should be able to cut it as well, but what's the fun in that.
Posts: 59
Joined: Mon May 28, 2012 1:41 am
Location: Baltimore, MD

Re: Anyone still building?

Postby pourcirm » Mon Jun 23, 2014 1:49 am

I got some aluminum plate and cut mine with a plasma cutter. A bit heavier than what everyone else probably has, but it sure makes the whole thing solid as can be. I'm trying to finish up the vents and decide my electronics before I cut and drill all the panel areas. I think once I get that all done I'm going to try and find a local place to powder coat them.
Posts: 25
Joined: Fri Jun 07, 2013 5:03 pm

Re: Anyone still building?

Postby OncleOh » Mon Jun 23, 2014 3:39 pm

acumulating parts,
- aluminium farame awaitng to be put together
- have to order makerslide profile
- will probably install larger laser tube like 80w reci
- DSP chosing one still
- have to order nema stepers and steper drivers
- ....

Hope to get all the parts in a short time.

Posts: 5
Joined: Sat Dec 08, 2012 10:39 am

Re: Anyone still building?

Postby jamese » Tue Jan 20, 2015 1:39 pm

Hi Guys

I am just starting my build. Where did you get your kits parts from. The website for the kits seems to be down for maintenance all the time?!

Any help gratefully received. Cheers.

Posts: 11
Joined: Mon Jul 23, 2012 7:35 pm

Re: Anyone still building?

Postby compatta » Tue Jan 20, 2015 8:45 pm

I just started building myself and i see that just like 3d printer projects, if its comes down to making sourcing easier, i think that can be a really big impact on making this project go forward.

-Sourcing for 3D Printable parts is becoming easier and Easier
-Sourcing for GT2 Pulleys and Belts is becoming easier
-Alternative electronics like the smoothieboard are now available. Electronics that still don't use a parallel port.

As opposed to making a laser cutter that is more replicatable, if it was just easier to source, i think more people would build it
knowing they can do other CNC like hobbies in one particular build area.

3.X Design?
Posts: 2
Joined: Tue Jan 13, 2015 5:15 am


Return to 2.x Laser Support

Who is online

Users browsing this forum: No registered users and 0 guests